Eufy S380 Setup

A high-performance robotic vacuum made for intelligent and effective cleaning is the Eufy S380. In order to configure the Eufy S380 setup, you must first unpack it, completely charge it, and then link it to the EufyHome app over Wi-Fi for remote control and personalization. For a steady connection, users need to make sure their Wi-Fi network is 2.4GHz. Mapping the cleaning area, setting up cleaning schedules, and modifying suction force according to floor types are all part of the setup procedure. The Eufy S380 setup is a great option for smart home settings since it provides accurate and automatic cleaning using AI-powered navigation and multi-floor mapping.

Eufy S380 Setup Manual

  1. Take the Eufy S380 out of the box along with its attachments.
  2. The HomeBase should be positioned on a level exterior close to a power vent and a wireless router.
  3. The vacuum should be fully charged before eufy setup.
  4. To activate the vacuum, press the power button.
  5. Verify the functioning of the indicator lights.
  1. Make sure the HomeBase is positioned against a wall and powered on.
  2. Before using the dustbin for the first time, empty it and attach the side brushes.
  3. To start cleaning, press the vacuum’s clean button.
  4. Keep an eye on its functionality and validate that the region is accurately mapped.

Eufy S380 Setup WPS

  • Make that WPS mode is supported by your Wi-Fi network.
  • Turn the HomeBase on by plugging it in.
  • Hold down the Eufy HomeBase’s Sync button until the light begins to blink.
  • Press the router WPS key within two minutes.
  • An effective linking will be established when the HomeBase’s Wi-Fi indicator turns solid.
  • To complete the Eufy S380 setup, use the EufyHome app and adhere to the on-screen directions.

Eufy S380 Setup With App 

  • From the App store, install the EufyHome app.
  • Unveil the app, then login or list in.
  • Make sure the HomeBase is switched on and turn on the Eufy S380.
  • In the app, choose “Add Device” and choose Eufy S380.
  • After choosing your 2.4GHz network, type in the password.
  • Await the vacuum’s connection and app registration.
  • Establish cleaning routines and preferences after connecting.
  • To confirm the connection, try a manual clean.

Eufy S380 Setup Issues And Solutions

1. An Unsuccessful Wi-Fi Connection

  • Make sure the network that the router is connected to is 2.4GHz, not 5GHz.
  • For a stronger signal, move the HomeBase closer to the router.
  • After restarting the Eufy S380, HomeBase, and router, reconnect.
  • Try again after resetting the EufyHome app’s Wi-Fi settings.

2. Device Not Detected By EufyHome App

  • Make sure your phone has both Bluetooth and Location Services turned on.
  • Try adding the device once more after restarting the phone and app.
  • Holding down the reset button for ten seconds will reset the Eufy S380.

3. Failure Of The WPS Connection

  • In two minutes of turning on WPS on HomeBase, press the router WPS switch.
  • Use the manual Wi-Fi configuration in the EufyHome app instead.
  • Restart both the router and HomeBase and try again.

4. No Reaction From HomeBase

  • Make sure it is plugged in correctly and check the power connection.
  • Hold the reset knob will perform a factory reset.

5. Firmware Updates Don’t Work

  • Ensure a solid internet connection through the apprise.
  • Try again after restarting HomeBase and the Eufy S380.
  • Use a different Wi-Fi network to try upgrading.

Eufy S380 Homebase WiFi Setup 

To know about eufy s380 homebase wifi setup follow these steps:

  1. The eufy s380 homebase wifi setup should be placed close to your router on a level, firm surface.
  2. Connect it to a power source.
  3. Hold down the HomeBase’s Sync button for a few seconds to get the LED to blink.
  1. Select Add HomeBase after launching the EufyHome app.
  2. Enter the password and select your Wi-Fi network (it must be 2.4GHz).
  3. A efficacious connection should be specified by the HomeBase LED turning solid. 

Factory Reset Eufy Homebase S380

1. Press The Button To Reset

  • Make certain that the HomeBase S380 is turned on.
  • Holding down the reset switch will cause the light to flash.

2. Use The App To Reset

  • Go to Settings > HomeBase S380 after using the EufyHome app.
  • Choose factory reset eufy camera, then click “Confirm.”

3. After Resetting, Reconnect

  • Follow the Wi-Fi setup instructions to re-configure the HomeBase.

Eufy S380 Firmware Update

  1. Go to Device Settings after launching the EufyHome app.
  2. To see what upgrades are available, tap Firmware Update.
  3. Tap Download & Install if there is an update available.
  1. Validate that WiFi is on for both the vacuum and the HomeBase.
  2. During the update, don’t switch the device off.
  3. After the update is installed, the vacuum will resume on its own.
Scroll to Top