Eufy S340 setup

The Eufy S340 setup consists of many critical phases. Start by installing the Eufy Security app on your device. Turn on S340 camera and validate that it is in an array of networks. Follow the app’s steps to set up an account or log in, then add a new device. To link, use your camera to scan QR code existing on the app. Once allied, you may alter options like motion detection, recording schedules, and notifications. Finally, use the accompanying hardware to install the camera in the chosen spot.

Eufy S340 manual setup

To manually set up the Eufy S340, follow these general steps.

  • Download the Eufy Security app.
  • Open the app and sign up or login.
  • Link the S340 camera to a power basis and make sure it is on.
  • Devices must be linked.
  • Trail app directions to scan the QR code with your camera.
  • Modify the settings
  • Use the accompanying hardware to put the camera in the preferred spot.

Eufy S340 WPS setup

  1. Transfer the Eufy Security app 
  2. Open the app and login.
  3. Link the Eufy S340 camera to a power basis and start it.
  4. Press the WPS knob on the WiFi router. This initiates WPS mode for an inadequate time.
  5. In the app, tap Add Device and choose the S340 model.
  1. Select the WPS setup option in the app.
  2. The software will prompt the camera to connect to the wifi via WPS.
  3. Wait for the app to authenticate your connection. Configure the camera settings as appropriate.
  4. Use the given hardware to place the camera in the chosen location.

Eufy solocam S340 setup

  • Get the app.
  • Make sure that the Eufy SoloCam S340 is turned on and associated with a power font.
  • Ascertain that your smartphone is linked to your wireless network.
  • Launch app, choose Add Device, then SoloCam S340.
  • A QR code will seem on the app. Using the camera, point at the QR code to connect.
  • Install the camera where you want it using the hardware that comes with it.
  • Make sure the targeted region is adequately covered by the camera’s vision.

Eufy S340 wifi setup

  • Get the Eufy Security app installed.
  • Turn on the Eufy S340 camera by joining it to a power basis.
  • Authenticate that the phone is allied to a wireless network.
  • Click on Add Device in the app, then choose S340 Camera.
  • It should immediately go to Eufy S340 setup mode on the camera. If not, use the camera’s reset knob.
  • Steer to WiFi settings on the phone and join the temporary network created by the camera.
  • Go to the app, choose the WiFi network at home, and input the passcode.
  • Hold off while the app finishes the Eufy S340 setup and verifies the connection.
  • Using the included hardware, install the camera, making sure it covers the designated region.

Eufy S340 firmware update

  • Open your smartphone’s Eufy Security application.
  • In the event that you haven’t already, log into your account.
  • To upgrade an S340 camera, tap on it.
  • Locate the “Firmware Update” option in the device settings.
  • To begin the update process, hit “Download” or “Update” if one is available.
  • The apprise is going to transfer and install on its own. During this procedure, do not unplug the camera or close the app.
  • Restart the camera if necessary to finish the update.
  • Make sure that following the upgrade, every camera feature is operating as intended.

Eufy S340 reset

  1. Verify that the Eufy S340 camera is turned on and operational.
  2. Trace the reset knob, which is frequently found on the camera’s bottom or rear.
  1. Hold the reset knob using a paperclip or other similar implement. Maintain it for ten to fifteen seconds.
  2. When the camera’s LED indicator begins to flash, which should happen in ten to fifteen seconds, remove the reset knob.
  1. Permit the camera to reload. The reset procedure will be shown by the LED indicator changing colors or patterns.
  2. After the reset is finished, go with the basic Eufy S340 setup steps on the Eufy Security app to reconfigure the camera.

Eufy S340 issues with setup and solutions

The following are typical Eufy S340 setup problems and their fixes:

Wi-Fi not connecting to the camera:

  • Solution: Verify that your smartphone is linked to the appropriate Wi-Fi network and that the connection is steady. See if the camera is getting a WiFi signal. Try the setup method once more after starting again your camera and network.

Camera Not Detected by App:

  • Solution: Verify that the camera is turned on and operating in Eufy S340 setup mode. Make sure your smartphone has GPS and Bluetooth enabled before restarting the Eufy Security app.

Failure to Scan a QR Code:

  • Solution: Make sure there is no blockage and the camera lens is clean. Maintain a solid grip and the appropriate distance amongst phone and camera. Make an effort to scan the QR code in a well-lit place.

Inadequate or unresponsive during Eufy S340 setup:

  • Solution: Look for any electrical interference from other gadgets. Give your smartphone and the camera a restart. Be sure that the app is running the fresh version.

Problems with Resets:

  • Solution: Authenticate that you are holding down the reset switch for an adequate amount of time. Try an alternate reset technique, if one is available, or get help from support if the camera still won’t reset.

Issues with Firmware Updates:

  • Validate that internet linking is firm as a solution. Try upgrading the firmware using the Eufy Security app once again after restarting the camera. 
Scroll to Top