Don’t worry if Eufy QR code not working while configuring your Eufy security camera. During the initial setup procedure, many customers encounter problems where the camera is unable to scan the QR code. This difficulty can keep you from properly finishing your Eufy setup, whether it’s a camera calibration issue, an inaccurate QR code, or an issue with the illumination.
This blog post will explore the most prevalent causes of your Eufy camera’s inability to scan a QR code, as well as the best fixes to get your device up and running as soon as possible.
Why It Matters To Use The Eufy QR Code?
You must use the Eufy Security app on your phone to scan a QR code that appears during the Eufy camera setup process. Because it includes setup information such as Wi-Fi login credentials and device pairing details, this code is crucial. Your camera cannot finish the setup procedure if you don’t scan this code, hence the problem of a Eufy QR code not working is really annoying.
Typical Causes Of Eufy Incorrect QR Code
1. An excessively high or low screen brightness
Inappropriate screen brightness is among the most prevalent problems. The Eufy camera lens can have trouble successfully reading the QR code if your phone’s brightness is too high or too low.
2. A dirty lens on a camera
The QR code may become blurry and illegible if the camera lens is dusty or unclean. This is especially typical if the gadget has been used outside or stored.
3. A phone that is cracked or scratched Display
Damage to your smartphone’s screen, particularly in the vicinity of the QR code, may cause the picture to become so distorted that the camera is unable to read it.
4. Inaccurate Angle or Distance
The QR code might not scan if you’re holding the phone at an unexpected angle or too close or distant from the camera.
5. Inadequate Lighting
The camera may have trouble detecting the QR code if you try to scan it in low light or in an area that is too bright, such as direct sunshine.
6. Outdated Firmware or App Version
Eufy QR code not working may also be caused by an out-of-date version of the Eufy Security app or the firmware on your camera. The eufy wrong QR code error might arise from this.
The “Eufy Camera Not Scanning QR Code” Issue May Be Resolved. Problem
1. Modify the brightness of the phone
Start by regulating the brightness of the screen. The ideal brightness range for showing the QR code is often mid-to-high.
2. Clear the lens of the camera
Wipe the Eufy camera lens carefully with a delicate microfiber towel. Verify that there are no smudges, dust, or other material on it.
3. Switch to a Different Tablet or Phone
Try displaying the QR code on a different device if your phone’s screen is broken or has poor resolution.
4. Modify the Angle and Distance
Keep your phone 5 to 8 inches from the lens of the camera. Move the phone carefully back and forth until the camera reads the QR code, making sure it is centered.
5. Make Lighting Better
Instead of aiming bright lights straight at the phone or camera, scan the QR code in a well-lit area. The finest lighting is natural inside.
6. Update the Firmware and App
Make sure the Eufy Security app is up to date on your device. Additionally, use the app settings to see if the firmware on your camera is up to date.
7. Reset Eufy camera
Resetting your Eufy camera from scratch might be helpful if none of the above-mentioned methods work. Hold down the SYNC switch for about ten seconds, or till a beep sounds. By doing this, you may return the camera to its original settings and begin the setup procedure over.
Trying the Eufy Setup again
Restart the Eufy camera configuration after implementing the aforesaid fixes:
- Go to your account by using the Eufy Security login screen.
- After choosing your camera model, tap “Add Device.”
- Until the QR code appears, adhere to the on-screen instructions.
- Present the QR code to the camera, then watch for an LED light or confirmation sound.
- Finally, finish the setup and Wi-Fi configuration.
Extra Success Advice
- Strong glare or matte screen protectors should be avoided as they may skew the QR code.
- If your phone is in dark mode, turn it off since it could influence how a QR code appears on some devices.
- Before doing the setup again, restart your phone, particularly if the screen isn’t updating properly.
Final Thoughts
It might be annoying to encounter the Eufy QR code not working problem, but it is typically resolved with a few easy tweaks. You can get beyond most obstacles by following the above procedures, regardless of whether the issue is caused by a dirty lens, dim illumination, or even a bright screen. Remember to make sure your firmware and app are up to date, and reset the Eufy camera if necessary. Your home security system will quickly get back on track when everything is configured.
FAQS:
1. How to set up the Eufy camera without scanning the QR code?
For initial setup, Eufy now needs scanning a QR code. There isn’t a recognized substitute approach. You can, however, try displaying the QR code on a different device or get in touch with Eufy support to discuss manual pairing possibilities.
2. What should I do if the QR code still doesn’t work?
Try cleaning the lens, changing the lighting, resetting the Eufy camera, and using a different phone if the QR code still won’t scan. Update the firmware and app if all else fails, or contact Eufy customer care for more help.
3. Does screen protector or phone case affect QR code scanning?
Indeed, heavy phone covers and screen protectors, particularly matte or privacy ones, can warp the appearance of the QR code, making it difficult to scan. The camera may read the code more precisely if they are removed during setup.
4. Is the QR code time-sensitive?
The camera may cease listening after a short while, however the QR code displayed in the app isn’t time-sensitive. Restarting the setup procedure will regenerate the code and restart the camera pairing mode if this occurs.